MI.PP-1007 Kinematic Viscometer bath
 |
Kinematic Viscometer Bath
|
It consists of water bath made of M. steel. Having
the illuminator at rear side. The temperature is controlled by electric
relay. It is supplied with one no. of mercury type thermometer and manometer
stand.
It is available in three different options for temp. range such as
ambient to 100ºC, 5°C TO 100 °C and ambient to 150 ºC
Note:
Bath can be fitted with P.I. D. controller extra cost.
Meets:- IS: 1206 part III
Following bath size is available.
- Size
a) 12" x 9" x 12" (To accommodate 4 viscometers)
b) 12" x 12" x 12" (To accommodate 6 viscometers)
c) 18" x 12" x 12" (To accommodate 8 viscometers)
MI.PP-1008 Universal Cone Penetrometer, Automatic
 |
Ductility Testing Machine
|
This apparatus is used for penetration on a wide
variety of material such as greases petroleum, bitumen tar wax and polish.
It consists of Timer (for setting the number of fall of needle) head support
mounted on a vertical rod, which can be adjusted for a height. Rack and
pinion assemblies provide a fine adjustment of needle tip to a sample and
incorporate slipping clutch mechanisms which make a reading of penetration
and subsequent resetting of a sample and accurate operation. The dial is
graduated from 0- 400 in one tenth millimeter sub division. It is supplied
with on e container and one set of needle.
Bitumen Cone Penetrometer Same as Above but without timer
MI.PP-1009 Loss of Heating/Thin film Oven
This dual-purpose oven is designed to determine:
- Loss in weight of bitumen and flux oils (loss on heating test)
- Effect of heat and air on asphaltic materials (thin film test)
Its salient features are
- The unit is heavily insulated and has a double glass door for viewing
the test chamber thermometer and samples.
- Temperature is controlled at 1630C (10C) by means of a variable
temperature controller and thermostat.
- Two rotating platform are supplied with each oven: one accepts 9
standard penetration cups for the loss on heating test, the other
accepts two 140 mm diameter test pans for the thin film test. The
platforms are rotated at 5 to 6 rpm by an external motor.
- Chamber dimensions 350 x 350 x 350 mm.
MI.PP-1010 Standard Tar Viscometer (cut back asphalt)
As per IP 71 and IS 1206 standards. It is used for
determination the viscosity of road oils and cut back bitumen. It consists
of S.S. bath with cup of 10mm or 4mm orifice and sleeve, stirrer with
lifting clip and ball. The assembly kept on suitable stand with levelling
screws. Operate on 220 volts AC mains.
A) Electrical heating with energy regulator control
B) Electrical heating with voltage varric control (copper coil)
Meets: - IS: 1206 (part 1)
MI.PP-1011 Say bolt Viscometer
It is used to determining the viscosity of fuel oil
and lubricating oil (thin and thick). The unit consists of stain less steel
bath oil cup that centrally placed in water bath. The bath has a lid, which
contains a water-cooling tube. Two handles with two starrier blades, the
thermometer soaked and a straight heater, stirring is done by turntable
arrangements. To operates on 220 volts AC 50 HZ.
MI.PP-1012 Carbon Residue, Conradson type
It is useful to determine amount of carbon residue
when an oil is evaporated under specified conditions. The carbon residue
values of crude oil, residual etc. These are useful in the manufacture of
various lubricants. The apparatus consists of spun sheet iron crucible 25cc
capacity. Sheet iron hood and sheet iron block on a stand, gas burner.
a) Conradson carbon residue single test apparatus
b) Conradson carbon residue four test apparatus with gas burner
Meets:- ASTM: D 189, IP-13
MI.PP-1013 Carbon Residue, Rams bottom type
It is made as per IP-14, ASTM 524 and is 1448 (P:8)
1967. Standard, it is used to determine the amount of carbon deposits when
oil evaporated under specified condition. The apparatus consists of a solid
metal bath having 5 wells to accommodate cocking bulbs. The heavy duty
heating elements provided around the bath. The heavy duty heating elements
provided around the bath. Supplied with 5 cocking bulbs, and one syringe.
a) Rams bottom, carbon residue apparatus with temp. regulation by energy
regulator, thermocouple and digital temp indicator in separate cabinets.
b) Rams bottom solid state ELECTRONIC TEMPERATURE controller and digital
temperature indicator in separate units
Meets:- IS: 1448, ASTM: D 524, IP-14
Optional Accessories
- Spare Cocking bulbs
- Spare heating element for above
- Spare syringes
- Stainless steel Tong
MI.PP-1014 Cloud & Pour point Apparatus suitable
for single test with insulated body
The pour point is the lowest temperature at which
the oil will just fail to flow. The apparatus consists of cooling bath made
of stainless steel sheet and stand unit drain plug and cover with provision
for fitting thermometer and filling aperture for adding freezing mixture.
Meets:- IS: 1448, ASTM-D 97, IP-15
MI.PP-1015 Cleveland Flash & Fire Point Apparatus
This apparatus is used for determination of flash
and fire point of petroleum products. The apparatus consists of a cleveland
Flash Cup made of brass, Gas Test-Jet Assembly, pivoted from a Cast Cup
Platform which is fixed to a Heating Bath. Energy Regulator to regulate rate
of rise in temperature. Suitable for operation of 230 V, 50 Hz, single
phase, AC supply.
Meets: - IS: 1449, ASTM-D92
MI.PP-1016 Digital Cleveland Flash Point Apparatus
 |
Digital Cleaveland Flash Point Apparatus
|
- Auto Temp. Control
- Stirring Manual
- Set point Temp. on controller
- Strudy Heater
- Power Coating Funis
